Available since MemSQL Ops version 4.1.8.

Stop, upgrade, and restart all MemSQL nodes in the cluster.

Usage

usage: memsql-ops memsql-upgrade [--settings-file SETTINGS_FILE] [--async]
                                 [--file-path FILE_PATH | --version VERSION | --version-hash VERSION_HASH]
                                 [--no-prompt] [--restart-on-rollback]
                                 [--skip-snapshot] [--skip-version-check]
                                 [--backup-data-directories | --no-backup-data-directories]
                                 [--stop-timeout STOP_TIMEOUT]

Stop, upgrade, and restart all MemSQL nodes in the cluster.

optional arguments:
  --settings-file SETTINGS_FILE
                        A path to a MemSQL Ops settings.conf file. If not set,
                        we will use the file in the same directory as the
                        MemSQL Ops binary.
  --async               If this option is true, we will exit without waiting
                        for the cluster to be fully upgraded.
  --file-path FILE_PATH
                        A .tar.gz file that contains a MemSQL binary to use
                        during the upgrade.
  --version VERSION     The MemSQL version to which all nodes will be upgraded
                        (e.g. 4.0.0). If this is not set, we will attempt to
                        upgrade all nodes to the latest available MemSQL
                        version.
  --version-hash VERSION_HASH
                        A MemSQL version hash to use.
  --no-prompt           If this option is specified, we will upgrade the
                        cluster without prompting. We will also assume
                        --backup-data-directories is set to true unless
                        otherwise specified.
  --restart-on-rollback
                        In the event of an upgrade failure and rollback,
                        restart the cluster. The default behavior without this
                        flag is to leave the rolled-back cluster in a stopped
                        state.
  --skip-snapshot       Do not run SNAPSHOT on all the databases in the
                        cluster before upgrading. This may cause the upgrade
                        to take longer.
  --skip-version-check  Do not check that the MemSQL version specified is
                        higher than the installed MemSQL version. This flag
                        only applies to maintenance release upgrades.
  --backup-data-directories
                        Backup data directories during the upgrade. If both
                        this and --no-backup-data-directories are not
                        specified, we will prompt before the upgrade.
  --no-backup-data-directories
                        Do not backup data directories during the upgrade.
                        Specifying this option will result in faster upgrades
                        and will use less disk space during the upgrade at the
                        risk of data loss. If both this and --backup-data-
                        directories are not specified, we will prompt before
                        the upgrade.
  --stop-timeout STOP_TIMEOUT
                        Number of seconds to wait for the MemSQL nodes to
                        stop. The default is 120 seconds.

Remarks

It is important to understand that an upgrade with memsql-ops memsql-upgrade installs a new version of MemSQL to a different path instead of overwriting the existing installation. Specifically, MemSQL Ops appends the last 10 digits of the randomly-generated memsql_install_id – a string that is created each time MemSQL is updated or installed – to the end of the installation directory name. For example: master-3306-FMGUB04J8R instead of master-3306. The older installation directory is deleted after a successful upgrade, leaving just the new path (i.e. master-3306-FMGUB04J8R).

By using a different directory to upgrade, the installation process can be safely rolled back, since the upgrade process does not modify any of the files in the older version’s directory.

Any custom scripts using a hardcoded path to the MemSQL installation directory should be updated to reflect the change of the installation directory caused by the upgrade, or, ideally, should use the memsql-path command instead of a hardcoded path. For more information, see MEMSQL-PATH.

Was this Article Helpful?

Thanks For Your Feedback!